Flexcompute integrates Siemens Calibre into PhotonForge

Flexcompute integrates Siemens Calibre into PhotonForge

Flexcompute now connects photonic circuit design with Siemens Calibre verification. PhotonForge 2.0 supports foundry design-rule and layout-versus-schematic checks through the established Calibre environment, allowing manufacturing constraints to be examined during circuit development.


IN Brief:

  • Flexcompute has formalised Siemens Calibre integration within its PhotonForge photonic design platform.
  • The integration supports nmDRC and nmLVS verification using foundry-specific rule decks.
  • Verification can be incorporated into iterative design workflows, including automated changes made by design agents.

Flexcompute has formalised the integration of Siemens Calibre verification software with PhotonForge 2.0, allowing photonic integrated circuit designers to incorporate foundry design-rule and layout-versus-schematic checking into their development workflows.

The integration supports Calibre nmDRC and nmLVS, which can operate using rule decks supplied by semiconductor foundries. It allows design teams to identify geometry and connectivity problems during circuit development, rather than relying exclusively on verification at the point of fabrication submission.

PhotonForge 2.0 was released in October as a platform combining schematic development, circuit simulation, physical layout, and verification for photonic integrated circuits. Its latest formal integration connects those activities with a widely used semiconductor verification environment.

The underlying Calibre checking functions had already appeared in PhotonForge’s technical documentation before the 18 November announcement. The development is therefore the formalised integration and associated workflow, rather than the first appearance of design-rule or layout-versus-schematic checking within the software.

Photonic integrated circuits contain optical structures that guide, modify, and detect light using semiconductor manufacturing processes. Waveguides, couplers, modulators, resonators, and optical interfaces must be arranged so that the fabricated circuit meets both its intended optical behaviour and the constraints of the selected manufacturing process.

Those constraints extend beyond the geometrical rules associated with conventional electronic interconnections. Optical structures may be sensitive to variations in width, curvature, spacing, layer alignment, and the properties of the surrounding materials.

A small dimensional change can alter optical propagation or coupling behaviour, even where the basic electrical connectivity of a circuit remains unchanged. Manufacturing verification must therefore be considered alongside optical simulation and the layout tools used to construct the design.

Design-rule checking, or DRC, compares the physical layout with a defined set of fabrication requirements. The checking software can identify structures that violate minimum widths, spacing rules, layer relationships, or other restrictions specified by the foundry.

Layout-versus-schematic checking, known as LVS, examines whether the physical implementation corresponds to the intended circuit description. It can identify missing or unexpected connections and discrepancies between the logical representation and the fabricated layout.

The two processes address different categories of error. A circuit may satisfy the foundry’s geometrical rules while containing incorrect connectivity, or it may represent the intended connections correctly while including features outside the permitted manufacturing dimensions.

Calibre provides separate engines for these checks. PhotonForge’s integration allows designers to invoke them from within their photonic development environment and inspect the resulting reports without treating manufacturing verification as an entirely separate stage.

Flexcompute states that the connector supports foundry rule decks in the form provided, including encrypted decks. This allows verification to use process-specific manufacturing requirements without requiring designers to extract or modify protected rule information.

The distinction is important because a generic set of geometrical checks cannot substitute for the exact rules applicable to a particular fabrication process.

Foundries may impose restrictions related to available materials, fabrication layers, process tolerances, and permitted device structures. A circuit intended for one process cannot automatically be assumed to comply with another.

Earlier verification can reduce the amount of rework required when a design contains an invalid geometry or unintended connection. Its effectiveness depends on maintaining the correct rule deck, device descriptions, and verification settings throughout the project.

PhotonForge also supports automated design workflows in which software agents modify circuit layouts or other design representations. Connecting those changes with Calibre verification allows the resulting layout to be checked as part of an iterative process.

Automated checking does not establish that an agent has made the correct engineering decision. The verification engine identifies compliance or violations against the supplied rules, while the interpretation of the results and the suitability of the modified design remain separate responsibilities.

An automatically generated layout may pass DRC and LVS while still failing to meet the optical performance required by the application. Insertion loss, coupling efficiency, thermal behaviour, and sensitivity to fabrication tolerances require other forms of analysis.

The integration also depends on suitable software access. Flexcompute’s documentation identifies the Calibre engine as a PhotonForge Enterprise capability, requiring the appropriate Photonic Canvas licence and access to the external verification environment.

Organisations adopting the workflow must therefore account for licensing, foundry process design kit access, software configuration, and the compatibility of their existing design data.

PhotonForge Enterprise also includes functions associated with supported foundry processes, design traceability, and collaborative development. These facilities provide a framework within which repeated verification can be associated with successive circuit revisions.

The wider objective is to maintain continuity between design, simulation, layout, and manufacturing verification, particularly as photonic circuits incorporate more components and become increasingly complex.

Flexcompute’s formal Calibre integration provides a route for applying recognised semiconductor verification tools within photonic circuit development. The resulting checks can establish compliance with selected rules, while optical performance, manufacturing yield, and completed device qualification remain dependent on additional analysis and testing.


Stories for you


  • EPC Space expands GaN transistor packaging options

    EPC Space expands GaN transistor packaging options

    EPC Space has expanded packaging choices for radiation-tolerant GaN transistors. Its 100–200V portfolio includes plastic QFN and hermetic options, providing different electrical, mechanical, and environmental configurations for satellite power conversion and aerospace equipment.


  • Samsung expands NVIDIA partnership into MLCCs

    Samsung expands NVIDIA partnership into MLCCs

    Samsung Electro-Mechanics has extended its semiconductor partnership with NVIDIA further. The companies have amended their substrate supply agreement and broadened cooperation involving high-reliability multilayer ceramic capacitors for accelerated computing platforms.