Toshiba expands low-noise LDO regulator range

Toshiba expands low-noise LDO regulator range

Toshiba has added thirty-five low-noise regulators for sensitive electronic circuits. Its TCR5FF series combines 500mA output capability, high ripple rejection, and fast load transient response in SOT-25 packages for industrial imaging, sensing, and analogue applications.


IN Brief:

  • Toshiba's TCR5FF series includes 35 fixed-output regulators covering 0.9V to 5.0V.
  • Typical specifications include 91dB ripple rejection at 1kHz and integrated output noise of 5µVrms.
  • The SOT-25 package supports conventional surface mount assembly and visual inspection of solder connections.

Toshiba Electronics Europe has introduced 35 low-dropout voltage regulators in its TCR5FF series, combining low output noise and fast load transient response with a package designed for conventional printed circuit board assembly.

The new devices provide fixed output voltages between 0.9V and 5.0V and support output currents up to 500mA. They are intended for applications including industrial cameras, precision sensors, measurement equipment, radio-frequency circuitry, and other electronics that require stable supply voltages.

The TCR5FF range uses a five-terminal SOT-25 package, adopting the electrical characteristics of Toshiba’s existing TCR5FM series while providing a leaded alternative to the smaller package used by the earlier devices.

Its introduction addresses two related requirements in power supply design: maintaining a stable output when load current changes rapidly and preventing unwanted electrical noise from reaching sensitive components.

Low-dropout regulators use linear control to maintain a specified output voltage from a higher input supply. Their operating characteristics differ from switching converters, which regulate voltage by transferring energy through periodically switched circuit elements.

Linear regulation can provide a relatively straightforward route to supplying sensitive analogue circuits, although the voltage difference between input and output creates power loss that must be considered in the thermal design.

A regulator’s transient response becomes important when the connected device rapidly changes operating state. A processor, image sensor, or communication component may move between low-power and active conditions, producing sudden changes in supply current.

The regulator’s control loop must respond to maintain the required output voltage. During the transition, the output can briefly rise or fall because the control circuitry and connected capacitors cannot compensate instantaneously for the change in current.

Toshiba states that the TCR5FF series improves load transient response from a no-load condition by approximately 80% compared with its earlier TCR3RM series, under the company’s specified test conditions.

At a nominal output of 2.8V, the manufacturer specifies a typical voltage deviation of -75mV when the load increases from 0mA to 100mA. When the load returns to zero, the typical positive deviation is 25mV.

For a larger transition between 1mA and 500mA, Toshiba specifies typical deviations of -60mV and +40mV for the corresponding rising and falling load changes.

These are measurements under defined electrical conditions rather than universal limits for every circuit. Actual behaviour depends on the selected regulator, input voltage, output capacitance, board layout, load transition, and operating temperature.

Power supply ripple rejection provides a different measure of performance. It describes how effectively the regulator prevents variations on its input supply from appearing at the output.

The TCR5FF series has a typical ripple rejection ratio of 91dB at 1kHz, measured under specified conditions. Its performance at other frequencies must be considered separately because ripple rejection varies across the frequency spectrum.

This distinction is relevant when the regulator is supplied from a switching converter. The converter’s operating frequency and associated harmonics may be substantially higher than 1kHz, so the quoted figure does not establish attenuation across every frequency that could be present.

Toshiba combines a bandgap reference, low-pass filtering, and a high-speed, low-noise operational amplifier within the regulator architecture.

The resulting typical integrated output noise is specified at 5µVrms. Such performance can be useful in circuits where variations in the supply voltage influence measurement accuracy or introduce interference into analogue signals.

Precision sensors and imaging circuits often contain signal chains that operate with relatively small electrical signals. Maintaining an appropriately controlled supply helps limit one potential source of disturbance, although total measurement performance also depends on the sensor, reference circuits, grounding, and signal-processing architecture.

The TCR5FF series operates from input voltages between 1.55V and 5.5V, subject to the requirements of the selected output voltage. Its operating temperature range extends from -40°C to +125°C.

For a 2.8V output at 500mA, Toshiba specifies a typical dropout voltage of 220mV under the stated conditions.

Dropout voltage represents the minimum input-to-output voltage difference required for regulation under a particular operating condition. If that difference becomes too small, the regulator may no longer maintain the intended output voltage.

The series also has a typical quiescent current of 10µA under no-load conditions and a typical standby current of 0.1µA. These characteristics contribute to the power budget of equipment that spends extended periods in low-power operating states.

The figures must be considered alongside the current consumed by the rest of the system. Low regulator quiescent current does not, by itself, establish the battery life of a complete device.

Thermal dissipation introduces a further constraint. In a linear regulator, power loss is approximately proportional to the voltage dropped across the device and the current delivered to the load.

A regulator supplying 500mA can therefore generate substantially different amounts of heat depending on its input and output voltages. The rated output current must be assessed alongside the permitted junction temperature and the thermal characteristics of the printed circuit board.

Toshiba’s SOT-25 package measures approximately 2.9 × 2.8mm, with a typical height of 1.1mm. Its leaded construction provides visible solder connections that can assist manufacturing inspection.

Package selection affects board area, assembly equipment compatibility, thermal performance, and access for inspection or rework. These considerations can be important when an electrical design must also meet established production requirements.

The new series retains the functional emphasis of the earlier TCR5FM devices while offering another mechanical integration option.

Toshiba’s electrical specifications provide a basis for evaluating the regulators in noise-sensitive systems, but component selection still requires verification of transient behaviour, ripple attenuation, output stability, and thermal performance under the intended operating conditions.


Stories for you


  • Samsung expands NVIDIA partnership into MLCCs

    Samsung expands NVIDIA partnership into MLCCs

    Samsung Electro-Mechanics has extended its semiconductor partnership with NVIDIA further. The companies have amended their substrate supply agreement and broadened cooperation involving high-reliability multilayer ceramic capacitors for accelerated computing platforms.


  • Vishay extends high-voltage capacitor range

    Vishay extends high-voltage capacitor range

    Vishay has expanded its high-voltage aluminium electrolytic capacitor product range. New 550V and 600V versions of the 259 PHM-SI series provide additional options for DC bus circuits in industrial drives, energy systems, and high-power conversion equipment.