IN Brief:
- RECOM has introduced a 300W isolated DC/DC converter family for industrial, automation, and railway applications.
- Three 4:1 input voltage ranges cover 9–36V, 18–75V, and 40–160V DC.
- The family offers seven output voltage options, remote control functions, and basic or reinforced isolation depending on the model.
RECOM has introduced the RP300H-(R)W series of isolated 300W DC/DC converters, extending its power conversion range for industrial, railway, and automation equipment. The family provides three wide input voltage ranges, seven output options, and different isolation configurations in a half-brick module intended for integration into electronic systems.
The new converters accommodate input ranges of 9–36V, 18–75V, and 40–160V DC. Each provides a 4:1 operating span, allowing the appropriate module to maintain output regulation across substantial variations in its incoming supply voltage.
The configurations correspond to applications using nominal 24V, 48V, and 110V DC supplies. Their broad input ranges provide flexibility where equipment must operate from different distribution systems or continue functioning during defined voltage fluctuations.
RECOM offers seven nominal output voltage options between 5V and 54V DC. These provide different supply arrangements for electronic loads, although the selected output voltage, current requirement, and operating conditions must remain within the specifications of the individual module.
The converters deliver rated power of 300W, with efficiency reaching 92.5% under specified conditions. That value represents the manufacturer’s maximum efficiency figure and should not be interpreted as a constant across all models, output voltages, input levels, and operating temperatures.
The modules use a half-brick package measuring 61.0 × 57.9 × 12.7mm without a heat sink. The format provides a compact board-mounted power conversion option for equipment containing control electronics, communications hardware, and other assemblies supplied from a common DC source.
Power density is one consideration when integrating a converter into an electronic system. Even a highly efficient module generates heat during conversion, requiring a suitable thermal path to prevent its internal components exceeding their permissible operating temperatures.
At 92.5% efficiency, a converter delivering 300W would dissipate approximately 24W as heat under the same conditions. That calculated example illustrates the scale of thermal management required, but it does not establish the actual loss for every model or operating point.
RECOM specifies a temperature range from −40°C to +105°C, subject to derating. The manufacturer also offers variants with pre-mounted heat sinks. The permissible operating load at elevated temperatures depends on the individual device’s thermal characteristics and the surrounding cooling arrangements.
The family provides input-to-output isolation rated at 3kV DC. Electrical isolation separates the incoming supply from the output circuit, allowing power transfer while maintaining an insulation boundary between the two sides.
The nominal 24V and 48V versions use basic isolation, while the 110V variants provide reinforced isolation. This distinction affects the converter’s suitability for installations requiring different levels of protection against electrical hazards.
The choice of insulation arrangement depends on the complete equipment architecture. Supply voltage, grounding, expected transient conditions, environmental exposure, and applicable safety standards determine the necessary isolation characteristics. A converter’s individual rating does not establish compliance for an entire installation.
RECOM has included remote on/off control with positive or negative logic, allowing a system controller to enable or disable the converter as required. This can be useful in equipment where individual power rails are brought online in a defined sequence or disconnected during particular operating states.
Remote sensing provides a means of compensating for voltage drops between the converter and the connected load. Feedback connections allow the converter to respond to the voltage at the load rather than relying entirely on measurements made at its own output terminals.
The output voltage can also be adjusted by as much as 20% below or 10% above the nominal setting, subject to the restrictions of the selected model. This allows some flexibility in matching the output to the requirements of the electronic assembly.
Integrated protection functions include responses to short circuits, overloads, overvoltage, and excessive operating temperatures. These mechanisms can protect the converter during abnormal conditions, although additional protection may still be necessary elsewhere in the finished equipment.
The series is specified in relation to IEC/EN 62368-1 safety requirements. RECOM also documents electromagnetic compatibility performance against EN 55032 Class A using external components, together with EN 55035. The EMC characteristics of the completed equipment will depend on its filtering, grounding, cabling, and installation design.
The converters extend RECOM’s existing industrial power portfolio, which also includes decentralised supplies for larger electrical loads. Unlike those standalone supply arrangements, the RP300H-(R)W family is intended for integration into electronic equipment requiring isolated DC conversion at board level.
RECOM lists individual configurations within the series, although several catalogue entries are marked as coming soon. General availability should therefore be confirmed for the required part number rather than assumed for every input and output combination.
The new family provides additional choices for 300W isolated conversion across three nominal DC supply classes. Its integration will depend on matching the selected module’s electrical ratings, insulation characteristics, thermal requirements, and protection functions to the equipment being developed.



