IN Brief:
- STDRIVE631P and STDRIVE631N combine three high-side and three low-side gate drivers for external MOSFETs or IGBTs.
- The two variants use positive-logic and negative-logic inputs, with 600V capability, integrated bootstrap diodes, and SmartShutdown protection.
- ST lists both SO-28 parts as active in volume production; evaluation boards support single- or three-shunt current sensing and different switch packages.
STMicroelectronics has highlighted its STDRIVE631P and STDRIVE631N gate-driver ICs for three-phase motor control and inverter designs. Each integrates three high-side and three low-side drive channels for external MOSFETs or IGBTs, together with bootstrap diodes and protective circuitry in an SO-28 package. The November technical presentation concerns existing products rather than a newly announced silicon release.
The two versions differ in the logic polarity of their control inputs: STDRIVE631P uses positive logic and STDRIVE631N negative logic. Both accept 3.3V and 5V-compatible input signals and are listed as active parts in volume production. ST’s first STDRIVE631P datasheet revision is dated March 2026, with evaluation documentation published subsequently, so the product history predates the November account.
A conventional three-phase inverter contains six power switches arranged as three half bridges, one pair for each motor phase. The upper and lower devices must be controlled in sequence to create the switching voltages required by the motor. The gate driver translates controller-level logic into higher-current pulses capable of charging and discharging the switches’ gate capacitances; the external transistors carry the load current.
The 600V rating describes the high-voltage rail capability of the driver, not the current rating or power output of the complete inverter. Those depend on the selected power devices, DC bus voltage, cooling, switching losses, and circuit design. The driver is therefore a control and interface component within a larger assembly rather than a replacement for the transistors or IGBTs that carry the motor current.
At 25°C, ST specifies 1.0A source and 0.85A sink gate-driver capability and an overall input-to-output propagation delay of 85ns. These figures help size a switching circuit but do not specify the power rating of an inverter or guarantee a particular switching time in every application. Gate charge, chosen resistors, circuit parasitics, junction temperature, and the driver’s supply all influence the final switching waveform.
Higher switching speed can reduce transition losses yet increase unwanted voltage spikes and interference. Inductance in the high-current loop produces overshoot as current changes, while fast voltage transitions couple through stray capacitance into signal and control circuits. ST quotes immunity to voltage slew rates of ±50V/ns for the driver. That component rating does not replace the need for layout verification, grounding, insulation coordination, or system-level electromagnetic compatibility testing.
Each half bridge must prevent its upper and lower switches from turning on simultaneously. Such cross conduction can produce a near-direct current path across the DC bus, imposing severe stress on the power devices. Interlocking and deadtime functions in the driver help manage switching overlap, while matched propagation delays reduce asymmetry between high-side and low-side command paths. The control strategy still needs to consider the minimum safe deadtime for its chosen switching devices.
The driver incorporates bootstrap diodes for the floating supplies used by its three high-side outputs. A bootstrap capacitor charges when the switching node and operating sequence permit it, then supplies a gate voltage above that node during high-side conduction. Combining the diodes on the IC reduces external components, but capacitor sizing, supply margins, duty cycle, and operating at very low switching frequencies still require design checks.
A built-in comparator and ST’s SmartShutdown function support fast overcurrent response, while under-voltage lockout monitors the low-side and high-side drive supplies. These protective functions depend on how faults are sensed and how the controller handles shutdown and restart. Device-level protection does not by itself establish functional safety or prevent damage under every short-circuit or thermal fault scenario.
The EVLSTDRIVE631P and EVLSTDRIVE631N demonstration boards provide three-phase inverter hardware using STGD6M65DF2 IGBTs and footprints that can accommodate DPAK or PowerFLAT 8×8 HV switches. Their current-sensing arrangements can be configured for one DC-link shunt or three shunts, with a microcontroller interface provided separately. The boards make it possible to evaluate switching and feedback methods against a real power stage, although the results remain dependent on the selected components and test conditions.
A single DC-link shunt reduces sensing hardware but requires software to reconstruct phase currents within suitable PWM sampling windows. Three-shunt arrangements offer more directly measured phase-current information at the cost of extra parts and routing. The demonstration platform supports approaches such as field-oriented control and six-step commutation; the gate-driver IC does not execute those motor-control algorithms itself.
ST positions the two drivers for equipment including fans, pumps, refrigeration compressors, and industrial inverters. Device selection still requires checks of switching loss, thermal design, fault thresholds, control timing, PCB clearances, and the selected power switches. Both parts are in volume production, while the November material documents their capabilities rather than establishing new qualification or first availability.



